Questions on pins MIX_I, MIX_Q, FILT_I and FILT_Q for ADF 7020
Dear Sir/Madam, My primary goal is to find the phase information of the received signal using a quadrature demodulation architecture receiver/transceiver. Therefore the signals I am most interested in...
View ArticleQuestion Regarding AD8339
Hello to everyone in Engineer Zone, I wish to post a technical inquiry about the AD8339. According to the datasheet for product AD8339 Revision B on page 29, and with reference to the section "using...
View ArticleClik here to view.
Query about REF192
Dear Team, Please explain or share information …about output shift with respective to temperature value(due to solder effect )…please see below information is available in REFf192 datasheet of page:21...
View ArticleWhat is TECGAIN of ADN8834 DS?
Hi, I have a question about TEC controller ADN8834. I can see an equation of f_0dB in DS at p18.Can you explain what TECGAIN in it? from Fig 35, 0dB should be at 1/(2*pi*R_1*C_1). But f_0dB of...
View ArticleHMC1048LC3B (MIXER 2 - 18 GHz)
Based on the data sheets for HMC1048LC3B (MIXER 2 - 18 GHz), can i used VCO input power with 8.52dBm. Currently i doing simulation in ADS software, can i still used the data as provided for vco 9dBm...
View Articlead5522-output voltage is a Sine wave when Fin is a constant
Dear Sir/Madam. I am using a extent range. A external amplier is connected to Exfoh.output voltage is a Sine wave when Fin is a constant. The frequence is 10K Hz.VREF is confirm as 5VThe supplies is...
View ArticleClik here to view.
Lithium Iron Phosphate batteries
I am using Lithium Iron Phosphate 3.7volt cell @ 4700mA.hour rating. I want to make batteries with output voltages of 24volts and 32volts. They will be recharged from photovoltaic panels only. 7...
View ArticleClarification on interfacing ADF7020
Hello, I am using ADF7020 (daughter board with 11.0592MHz XTAL) to design a RF UHF reader which reads the data in the RFID tag (passive), as the tag comes within the range. I use dsPIC33fj256gp710 for...
View Articleadf7021-N
which is the best protocol to interface adf7021-N with a microcontroller and why
View Article3 lead ECG
I am planning to build a wireless ECG sensor. This is my first attempt to do anything of this sort. I was wondering if i should go AC-coupled AFE or DC-coupled AFE? Which one would be easier?
View ArticleAbout ADF7023's Daugher board
Hi, I bought ADF7023 daughterboard, and I found the antena in the box.But I can find any information on this antena.Could you tell me How I can get the datasheet of it? Best,Tarzan
View ArticleSimulation software and a library for ADN3000-06 ic
I am a university student doing my final year university project.Part of My project is to design a fiber optic receiver.I am employing Analog devices ADN3000-06-50A-PT7 ic for this purpose.I am...
View Articletime-to-digtial or time-to-analog converter
We need to measure the time duration between two pulses (separation range 5ns to 40ns, resolution <200ps, >50k measurements/s). I searched analog.com but did not find any chip dedicated for such...
View ArticleClik here to view.
ADA4571, min and max pitch between two poles when linear config.
Hi, Regarding to AMR angle sensor ADA4571 when used in linear configuration, I would like to know,a) Minimum and Maximum pitch between a north and south pole which available to be used.b) Accuracy data...
View ArticleClik here to view.
Having noise problems w/ AD1988A / ASUS/ M2N-SLI Deluxe
I have the latest drivers and a creative 7.1 speaker setup. My monitor is a Olevia 42 inch LCD TV. I have this background hum. Just like when a guitar is plugged into an amp. There are times when it...
View ArticleSMP04ESZ Sample & Hold drifting
I'm having a problem where the non activated lines from my sample and hold circuit is drifting up. Everything is fine as long as I am switching at 1 Hz or greater, but in some case I want to keep the...
View ArticleADN8831 - Which FET should I use?
Hi, I have a customer developing a circuit based on AN-695 schematic. The FET indicated (FDC6020C) is obsolete, so I would like to know which other FET's can I recommend them. Thanks,Fernando Guerra
View Articleadf7021-N
hi everyone;my name is harsha ;i wanted to program adf7021-N eval board with msp430F5438A experimental board . the interface part is the problem the header jacks are not identical so can anyone suggest...
View ArticleADCMP572 VTT pin confusion
We've received 2 ADCMP572 eval boards, but unfortunately the documentation for the part and the eval board seems to be inconsistent.As a result, I have a question: should VTT (pin 8) be tied to GND or...
View ArticleClik here to view.
do you have samples of the new material that will be used for part #...
do you have samples of the new material that will be used for part # ADR5043BKSZ-R2?
View Article