ADXL001 Output filtering
Data sheet recommends a 1nF capacitor on the output.Table says a minimum of 1000pF (1nF).Other devices publish the output resistance to make understanding the device behavior easier.Data sheet of the...
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View ArticleClik here to view.
AD5242 used as varying resistor with LM317 to get analog voltage
I am trying to get analog voltage with AD5242 and LM317. I get both the ICs working seperately but when I use the resistor value I created with AD5242 on the LM317, it doesn't work as expected. I...
View ArticleA series of questions about ADATE318
1. How to get the ibis model of the ADATE318?2. What the difference between the pin PPMU_Sx and PMU_Sx? How to use these pins in application?3. How to connect the kinds of GND in the application, such...
View ArticleClik here to view.
Controlling digital potentiometer (AD5142) by Arduino UNO
Hi, I am trying to control digital potentiometer (AD5142) by Arduino UNO.Here is the pin configuration of AD5142.I connect SCLK pin to 13 pin of Arduino (serial clock pin), SDI pin to 11 pin of Arduino...
View ArticleClik here to view.
ADF7023 is IEEE 802.15.4g compliant?
I'm wondering if ADF7023 is effectively 4g compliant.Looking to the packet format reported in the datasheet, it seems different from the packet formatspecified in the 4g standard ( i.e. PHR in 4g is 2...
View Articledemodulation sin o square wave?
Hi,i'd like to use AD8333 to demodulate a pass-band signal with 200kHz local oscillator.The datasheet says that i can use both sin wave and square wave. My question is:The use of a square wave produces...
View Articledo you have samples of the new material that will be used for part #...
do you have samples of the new material that will be used for part # ADR5043BKSZ-R2?
View ArticleAD5522 Eval Board idle temperature
Hi, My customer noticed that the AD5522 Eval Board run hot when idle(no load ,output disable) ca. 70°C From the reference design, ADI does not mention any heat sink required .Is this typical? I doubt...
View ArticleClik here to view.
AD5522 can not communicate via SPI?
Hi All: I have a AD5522 Evaluation Board,and it's work well on Evaluation Software 1.6.1. Now I want to use my STM32F103ZE to control the AD5522,but I can't communicate with AD5522 via SPI.It's...
View ArticleClik here to view.
ADN8834, Amplifers
Hallo, are the two chopper stabilized amplifers inside the ADN8834 on while the chip is in standby. I plan implementing a digital control loop arournd the AD8834. It want to use one of the amplifiers...
View ArticleGFSK transceiver multi carrier frequence & multi baud rate
Hello, I am looking for a tranceiver multi carrier frequence & multi baud rate for the ISM band 868 MHz, I have seen the component...
View ArticleMesh network with ADF7021
Hi all, I have interfaced an ADF7021V for transferring a realtime biomedical signal. Now I would like to create a mesh network for data transfer with this device. Is the higher layer protocols...
View ArticleSimulation Pspice AD694
Bonjour, Je souhaite réaliser une sortie 0_20mA et 4_20mA en utilisant la sortie 0 ... 3V de mon DAC. Pour cela je souhaite utiliser le composant AD694 de analog devices. Mais avant d'aller plus loin,...
View ArticlePSpice models
Hi Engineers, I am trying to simulate a circuit on my PC using one of Analog Devices models, "ADA4817 SPICE Macro Model" I am having trouble using this circuit model file and finding information on how...
View ArticleClik here to view.
AD5242 used as varying resistor with LM317 to get analog voltage
I am trying to get analog voltage with AD5242 and LM317. I get both the ICs working seperately but when I use the resistor value I created with AD5242 on the LM317, it doesn't work as expected. I...
View ArticleA series of questions about ADATE318
1. How to get the ibis model of the ADATE318?2. What the difference between the pin PPMU_Sx and PMU_Sx? How to use these pins in application?3. How to connect the kinds of GND in the application, such...
View ArticleAbout ADF7023's Daugher board
Hi, I bought ADF7023 daughterboard, and I found the antena in the box.But I can find any information on this antena.Could you tell me How I can get the datasheet of it? Best,Tarzan
View ArticleClik here to view.
How to connect a laser with common PD-anode and LD-cathode to ADN2847?
Hi All, I'd like to know a following point about ADN2847 application circuit.According to Figure 15 in the datasheet of ADN2847(RevB), a laser with common PD-cathode and LD-anode is used for this...
View Article