ESD Ratings for ADR5040/ADR5041
Hello, I need the ESD rating test date for the following two devices: ADR5040BKSZ-REEL7ADR5041BKSZ-REEL7 I also would like to know what test standard(s) is used for ESD qualification? Is there a link...
View ArticleDifference between ADN8834CB-EVALZ and ADN8834MB-EVALZ
What is the difference between ADN8834CB-EVALZ and ADN8834MB-EVALZ? Do you have any additional information or datasheet for the eval kits?
View ArticleWhat is TECGAIN of ADN8834 DS?
Hi, I have a question about TEC controller ADN8834. I can see an equation of f_0dB in DS at p18.Can you explain what TECGAIN in it? from Fig 35, 0dB should be at 1/(2*pi*R_1*C_1). But f_0dB of...
View ArticleClik here to view.
AD5522 can not communicate via SPI?
Hi All: I have a AD5522 Evaluation Board,and it's work well on Evaluation Software 1.6.1. Now I want to use my STM32F103ZE to control the AD5522,but I can't communicate with AD5522 via SPI.It's...
View ArticleCategory of VisualAudio Discussion
Hi, VisualAudio is a very good program for developing audio application using ADSPs. A separate category for it must be very popular. Thanks,Zwone.
View ArticleAbout how to use ADN2818
So I'm outsider of SONET, I query you about foundamental usage of ADN2818. Q1.I want to use it as clock and data separater from "enbedded clock signal" like a 8B10B. If it possible,Q2.Dose it can...
View ArticleAD22151 Eval Board
Hello, I am looking for an eval board for the AD22151. Is there one that is available? Thanks!
View ArticleADN8834, Amplifers
Hallo, are the two chopper stabilized amplifers inside the ADN8834 on while the chip is in standby. I plan implementing a digital control loop arournd the AD8834. It want to use one of the amplifiers...
View Articleapplication ADN2841
Hello!I am going to use ADN2841 in my design, but I have got some questions.1. The ADN2841 is very good for our conditions, but it has a small current of modulation. I have got a laser diode module...
View ArticleClik here to view.
AD5520:trouble with MEASOUT voltage range
HI this is my sch of ad5520. the pin 64(CLL) vee_3v3 is -3.3V and pin 63(CLH) vcc_3v3 is +3.3v.I change the pin 26(FIN) voltage , the pin 58 (MEASOUT) should from -3.3V to + 3.3V . but the pin 58...
View ArticleQuestion about test setting of ADN8834
Hello, My customer wants to confirm the performance of ADN8834 using EVM first.And they are trying to test a ADN8834 EVM and TOSA module with Thermoelectric Cooler (from NeoPhotonics.) During the test,...
View Articleadf7021-N
which is the best protocol to interface adf7021-N with a microcontroller and why
View ArticleADCMP572 VTT pin confusion
We've received 2 ADCMP572 eval boards, but unfortunately the documentation for the part and the eval board seems to be inconsistent.As a result, I have a question: should VTT (pin 8) be tied to GND or...
View ArticleSimulation software and a library for ADN3000-06 ic
I am a university student doing my final year university project.Part of My project is to design a fiber optic receiver.I am employing Analog devices ADN3000-06-50A-PT7 ic for this purpose.I am...
View ArticleADF7021 Daughter board ADF7021DBZ5
Hi, I have this daughter board (ADF7021DBZ5) which i will stream to 144 MHz, then my question is, which components I need on this board to transmit at the desired frequency?, Since this board does not...
View ArticleAD5522 Eval Board idle temperature
Hi, My customer noticed that the AD5522 Eval Board run hot when idle(no load ,output disable) ca. 70°C From the reference design, ADI does not mention any heat sink required .Is this typical? I doubt...
View ArticleADF7012 RF output impedance
Dear, Can anyone kindly provide us RF output impedance of ADF7012 around 145MHz?We'd really appreciate if anyone has data on this as we're not equipped with load-pull measurements. Thank you in...
View ArticleClik here to view.
Questions on pins MIX_I, MIX_Q, FILT_I and FILT_Q for ADF 7020
Dear Sir/Madam, My primary goal is to find the phase information of the received signal using a quadrature demodulation architecture receiver/transceiver. Therefore the signals I am most interested in...
View ArticleEVAL-ADF70XXMBZ2
hi, May I ask for a copy of the source code of chip programming software which display the data received by the EVAL-ADF70XXMBZ2 connected to a host PC transmitted by another EVAL-ADF70XXMBZ2 via RF...
View ArticleDrawing for Tray 64 Ld. LQFP 10x10
Dear Sir/Madam, Where can I find your drawing for tray 64 Ld. LQFP 10x10 as AD7658BSTZ-1 on your webpages?If it is not put on your web page, can you send it to me by pdf style?I would like to confirm...
View Article