ADN8831 TEC controller - 24 Voltage Application?
Customer is are going to settle on 24V for system voltage. Weblink for the TEC chip (http://www.kryotherm.ru/modulez/down.phtml?filename=/dir2attz/Frost-74.pdf)spec. As you can see at dT=50C the...
View ArticleAbout ADF7023's Daugher board
Hi, I bought ADF7023 daughterboard, and I found the antena in the box.But I can find any information on this antena.Could you tell me How I can get the datasheet of it? Best,Tarzan
View ArticleADN8831 TEC Controller Application
Hello I’m an engineer in koreaI’ll make a TEC control board using ADN8831And the TEC is 170~300W, so I need to use 24V power supply for FET power(Vds)But the IC(ADN8831) is designed for maximum...
View ArticleClik here to view.
Simulation software and a library for ADN3000-06 ic
I am a university student doing my final year university project.Part of My project is to design a fiber optic receiver.I am employing Analog devices ADN3000-06-50A-PT7 ic for this purpose.I am...
View ArticleEDA TOOLS METHODOLOGY FOR LAB-ON-A-SMARTCARD
I am looking for experts in EDA Tools Mthodology for LAB-ON-A-SMARTCARDPlatform (Analog Mixed Signal):Here is the...
View ArticleADF7012 capable of Biphase L Modulation
Hello:Is the ADF7012 capable of biphase L modulation scheme? The application would be for search and rescue beacon transmitter.Thank you,Frank
View ArticleECG HOLTER MONITOR DESIGN
Hello Bill, I am currently working on a layout design for this ADI solution. I have a few questions regarding the circuit presented here: From the biomedical point of view, what are the minimum...
View ArticleLiedi
Hello,i have to develope a 4 channel EMG-measurement system by very small power consumtion and optimal chip disign. For input stages i found in the literature only dc-coupled instrumentation amplifiers...
View ArticleADF7021-N TEST PATTERN GENERATOR
When using the following setting modulation+test patterns on the ADF7021-N (EVAL-ADF7021-NDB),I get the incorrect frequency, or not change setting frequency.Does the combination of Modulation+Test...
View ArticleDrawing for Tray 64 Ld. LQFP 10x10
Dear Sir/Madam, Where can I find your drawing for tray 64 Ld. LQFP 10x10 as AD7658BSTZ-1 on your webpages?If it is not put on your web page, can you send it to me by pdf style?I would like to confirm...
View ArticleADF7025 for Wireless audio with ADAU144x DSP
Hi Guys Is there any information on using this as a wireless audio TX/RX im looking at adding wireless transmission to my DSP. I have looked at the data sheets but they all reference the BlackFin DSP...
View ArticleAre source codes available for EVAL-ADF70xxMBZ2 and EVAL-ADF7021DBZ2?
Hi,I would like to have a copy of all available source codes for EVAL-ADF70xxMBZ2 and EVAL-ADF7021DBZ2.email: aishamagayoong@yahoo.comThank you very much. Sitti
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View Article3 lead ECG
I am planning to build a wireless ECG sensor. This is my first attempt to do anything of this sort. I was wondering if i should go AC-coupled AFE or DC-coupled AFE? Which one would be easier?
View ArticleADN8831 - Which FET should I use?
Hi, I have a customer developing a circuit based on AN-695 schematic. The FET indicated (FDC6020C) is obsolete, so I would like to know which other FET's can I recommend them. Thanks,Fernando Guerra
View ArticleADN8831 TEC Controller Application
Hello I’m an engineer in koreaI’ll make a TEC control board using ADN8831And the TEC is 170~300W, so I need to use 24V power supply for FET power(Vds)But the IC(ADN8831) is designed for maximum...
View ArticleQuery about ADN8831
hello, I have some queries about ADN8831's EVB.1, in figure 12 of its datasheet, the resistors and capacitors at OUT1 and OUT2 are no specific values, could you please help suggest the typical values...
View ArticleProblem starting EVAL-AD9837SDZ software
Analog Engineers, I have two EVAL-AD9837SDZ boards that I would like to program on my computer, but I am having an issue getting the software to open. The program can't locate the LabVIEW Run-Time...
View ArticleAD630 Lock-in Amp
Hello everyone, I am looking to implement a lock-in amplifier in the range of 100kHz to 1MHz to obtain amplitude and phase information. Any thoughts on whether the AD630 will be ok for this frequency...
View ArticleLithium Iron Phosphate batteries
I am using Lithium Iron Phosphate 3.7volt cell @ 4700mA.hour rating. I want to make batteries with output voltages of 24volts and 32volts. They will be recharged from photovoltaic panels only. 7...
View Article