ADF7012 programming by parallel port
Hi, i need program the device by parallel port, so, i need run ADI LINK ADF7012 Rev 2.1, right? i can´t find the software at Analog Device Website,where will i find it?Thanks.
View ArticleEVAL-ADF70XXMBZ2
hii am currently evaluating EVAL-ADF7021DBZX using EVAL-ADF70XXMBZ2 mother board.i am interested to know how you implemented the Chip Programming Software.the purpose of my study is to be able to know...
View ArticleHow can I get the ADRadioNet for ADF7023?
Is the protocol developed by ADI available for ADF7023?How can I download it?
View ArticleEVAL-ADF70XXMBZ2
hi, May I ask for a copy of the source code of chip programming software which display the data received by the EVAL-ADF70XXMBZ2 connected to a host PC transmitted by another EVAL-ADF70XXMBZ2 via RF...
View ArticleADN2830 Laser Diode Controller
I have spun a board for the ADN2830 to control a JDSU laser with internal photo detector. The good news is both the cathode and anodeare isolated from the case. I'm using two in master/slave as I need...
View ArticleSimulation software and a library for ADN3000-06 ic
I am a university student doing my final year university project.Part of My project is to design a fiber optic receiver.I am employing Analog devices ADN3000-06-50A-PT7 ic for this purpose.I am...
View ArticleHow to connect a laser with common PD-anode and LD-cathode to ADN2847?
Hi All, I'd like to know a following point about ADN2847 application circuit.According to Figure 15 in the datasheet of ADN2847(RevB), a laser with common PD-cathode and LD-anode is used for this...
View ArticleADA4571 Evaluation Software doesn't be opened
Hi All, I am now trying to install the ADA4571 Evaluation Software into my PC, it doesn't work so far.I am trying to install it along with the installation procedure written in theUG-739.The software...
View ArticleADAS1000 CMRR
Hi, We have a customer who is designing the ECG devices but there is a requirement on the CMRR (Balanced) of > 120dB at mains frequency, with patient cable. Can ADAS1000 perform such a CMRR...
View ArticleADF7025 for Wireless audio with ADAU144x DSP
Hi Guys Is there any information on using this as a wireless audio TX/RX im looking at adding wireless transmission to my DSP. I have looked at the data sheets but they all reference the BlackFin DSP...
View Articleapplication ADN2841
Hello!I am going to use ADN2841 in my design, but I have got some questions.1. The ADN2841 is very good for our conditions, but it has a small current of modulation. I have got a laser diode module...
View Articlehelp reading adxl312 (spi 4 wire)
hi,i am having trouble reading acceleration data from adxl312, this accelerometer can be read/write similar to adxl345. below is my code, it doesn't work, no matter how much i shake it i get only 0...
View ArticleADF7012 capable of Biphase L Modulation
Hello:Is the ADF7012 capable of biphase L modulation scheme? The application would be for search and rescue beacon transmitter.Thank you,Frank
View ArticleClik here to view.
ADA4571 Evaluation Software doesn't be opened
Hi All, I am now trying to install the ADA4571 Evaluation Software into my PC, it doesn't work so far.I am trying to install it along with the installation procedure written in theUG-739.The software...
View ArticleECG RLD
Hello Bill 1) What should be the RLD voltage level & how much current can I inject into the body. The Instrument is powered from 3v battery and single supply design.2) Does the RLD voltage level...
View ArticlePhysical measurement principle ADIS Analog Devices
hello,I'm interested inthemeasurement principleof the ADIS16006. Does thisworksoncapacitive,orpiezoelectricalprinciple? If piezoelectrical principle, electrical or resistive?Thanks for the comment.
View ArticleClik here to view.
Having noise problems w/ AD1988A / ASUS/ M2N-SLI Deluxe
I have the latest drivers and a creative 7.1 speaker setup. My monitor is a Olevia 42 inch LCD TV. I have this background hum. Just like when a guitar is plugged into an amp. There are times when it...
View ArticleADF7020-1 question
I want to be able to offer two frequency ranges, one being ~600MHz and the other being ~900 MHz. I'm wondering if I can expand the range of the 7020-1 to get up to the 900MHz. It looks like the -1...
View ArticleSingle supply ECG front end without RLD
How can we realize a single supply ECG front end without using Right Leg Drive? Thanks.
View ArticleSynq DLP 6 processor
i have this processor but the sound quality i am not happy with. the bass is so weak, the bass guitar and the foot drum can be hardly heard. could you please ***
View Article
