Are source codes available for EVAL-ADF70xxMBZ2 and EVAL-ADF7021DBZ2?
Hi,I would like to have a copy of all available source codes for EVAL-ADF70xxMBZ2 and EVAL-ADF7021DBZ2.email: aishamagayoong@yahoo.comThank you very much. Sitti
View ArticleEVAL-ADF70XXMBZ2
hi, May I ask for a copy of the source code of chip programming software which display the data received by the EVAL-ADF70XXMBZ2 connected to a host PC transmitted by another EVAL-ADF70XXMBZ2 via RF...
View Article3 lead ECG
I am planning to build a wireless ECG sensor. This is my first attempt to do anything of this sort. I was wondering if i should go AC-coupled AFE or DC-coupled AFE? Which one would be easier?
View Articledemodulation sin o square wave?
Hi,i'd like to use AD8333 to demodulate a pass-band signal with 200kHz local oscillator.The datasheet says that i can use both sin wave and square wave. My question is:The use of a square wave produces...
View ArticleSupply voltage for temp sensor ADATE318
What is supply voltage (VDD_TERM) for temp sensor ADATE318. I did not find this information in the datasheet.
View ArticleA series of questions about ADATE318
1. How to get the ibis model of the ADATE318?2. What the difference between the pin PPMU_Sx and PMU_Sx? How to use these pins in application?3. How to connect the kinds of GND in the application, such...
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View ArticleADN2841 input to output propagation delay
Hello, Do you have any data for ADN2841 input to output(IMODP) propagation delay at 25C degree and Vcc=5V? Best regards and Thanks,Ian
View ArticleESD Ratings for ADR5040/ADR5041
Hello, I need the ESD rating test date for the following two devices: ADR5040BKSZ-REEL7ADR5041BKSZ-REEL7 I also would like to know what test standard(s) is used for ESD qualification? Is there a link...
View ArticleAD5242 used as varying resistor with LM317 to get analog voltage
I am trying to get analog voltage with AD5242 and LM317. I get both the ICs working seperately but when I use the resistor value I created with AD5242 on the LM317, it doesn't work as expected. I...
View Article320*240 resistive touch screen calibration problem
Hi every one.I have 320*240 LCD with resistive touch screen and touch screen controller of AD7843 ( All is together in one LCD from topway: KM2088S). I want to know what is the best way to calibrate...
View ArticleAD 73360 not working correctly....?
i have just got the chance to work on ad73360. Our signal range is +/-1.6. and according to ad73360 it shall work fine for this range. we are using it in single ended mode. now there are the problem i...
View ArticleADA4571 sensing tooth of gear wheel
Hello, Below is a figure copied from CN0332.AMR sensor senses magnetic field. Gear wheel or rack is not a magnet. I wonder how magetic field is created from a metal as shown the figure? Is a specific...
View ArticleCan EVAL-ADF70xxMBZ2 detect sticky tag
Hello, I am using a sticky tag from Alien Technologies (ALN-9640 Squiggle® Inlay). Can the EVAL-ADF70xxMBZ2 (with ADF7020 DB) read the data from this tag. I am using 'ADIismLINK config SW' to display...
View ArticleADF7012 RF output impedance
Dear, Can anyone kindly provide us RF output impedance of ADF7012 around 145MHz?We'd really appreciate if anyone has data on this as we're not equipped with load-pull measurements. Thank you in...
View ArticleADF7242 Payload
We are looking for an RF transceiver to be used for data streaming. The ADF7242 seems to have a 128 byte limitation to the packet size.Anybody knows how much data can we send on the same channel during...
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View Articleapplication ADN2841
Hello!I am going to use ADN2841 in my design, but I have got some questions.1. The ADN2841 is very good for our conditions, but it has a small current of modulation. I have got a laser diode module...
View ArticleWhat is TECGAIN of ADN8834 DS?
Hi, I have a question about TEC controller ADN8834. I can see an equation of f_0dB in DS at p18.Can you explain what TECGAIN in it? from Fig 35, 0dB should be at 1/(2*pi*R_1*C_1). But f_0dB of...
View ArticleADF7020-1 question
I want to be able to offer two frequency ranges, one being ~600MHz and the other being ~900 MHz. I'm wondering if I can expand the range of the 7020-1 to get up to the 900MHz. It looks like the -1...
View Article