Mesh network with ADF7021
Hi all, I have interfaced an ADF7021V for transferring a realtime biomedical signal. Now I would like to create a mesh network for data transfer with this device. Is the higher layer protocols...
View Articleapplication ADN2841
Hello!I am going to use ADN2841 in my design, but I have got some questions.1. The ADN2841 is very good for our conditions, but it has a small current of modulation. I have got a laser diode module...
View ArticleEDA TOOLS METHODOLOGY FOR LAB-ON-A-SMARTCARD
I am looking for experts in EDA Tools Mthodology for LAB-ON-A-SMARTCARDPlatform (Analog Mixed Signal):Here is the...
View ArticleFrequency in high volt, low HZ
Gentlemen (and ladies) I am a basic homewire electrician, not at all on par in this domain, so please forgive this intrusion. I am hoping for a yes or no type response to my query. I am attempting an...
View ArticleClik here to view.
AD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View ArticleQuestion Regarding AD8339
Hello to everyone in Engineer Zone, I wish to post a technical inquiry about the AD8339. According to the datasheet for product AD8339 Revision B on page 29, and with reference to the section "using...
View ArticlePSpice models
Hi Engineers, I am trying to simulate a circuit on my PC using one of Analog Devices models, "ADA4817 SPICE Macro Model" I am having trouble using this circuit model file and finding information on how...
View ArticleSupply voltage for temp sensor ADATE318
What is supply voltage (VDD_TERM) for temp sensor ADATE318. I did not find this information in the datasheet.
View ArticleClik here to view.
ADA4571 sensing tooth of gear wheel
Hello, Below is a figure copied from CN0332.AMR sensor senses magnetic field. Gear wheel or rack is not a magnet. I wonder how magetic field is created from a metal as shown the figure? Is a specific...
View ArticleAD8672 Open-Loop Gain and Phase Shift vs. Frequency & Output Impedance vs....
Hi there, We are using the SPICE model of AD8672 to simulate the open-loop gain & phase shift vs. frequency & output impedance vs. frequency. It turns out to be quite different from the...
View ArticleWhat is TECGAIN of ADN8834 DS?
Hi, I have a question about TEC controller ADN8834. I can see an equation of f_0dB in DS at p18.Can you explain what TECGAIN in it? from Fig 35, 0dB should be at 1/(2*pi*R_1*C_1). But f_0dB of...
View ArticleUsing ADMP504 as part of the stethoscope
Hi, I am using AMDP504 as the input detector for a stethoscope design. Do we have any stethoscope cone housing recommendation that can be suitable for this mems part? Thanks. Best Regardsadrian chia.
View ArticleThe ADF7023 the AES encryption and decryption functions configuration Issue
First of all, my experiment is described as follows:with single-chip SPI and GPIO, MOSI, MISO, SCLK, CSN, and IRQ_GP3 pick heel ADF7023 connection.firmware running on a single-chip-based...
View ArticleADA4571 Evaluation Software doesn't be opened
Hi All, I am now trying to install the ADA4571 Evaluation Software into my PC, it doesn't work so far.I am trying to install it along with the installation procedure written in theUG-739.The software...
View ArticleClik here to view.
Problem starting EVAL-AD9837SDZ software
Analog Engineers, I have two EVAL-AD9837SDZ boards that I would like to program on my computer, but I am having an issue getting the software to open. The program can't locate the LabVIEW Run-Time...
View ArticleADF7023 Transceiver Problems
Hi ! Here is some ADF7023 issues . please check if they should be added in errata . 1) Manchester coding and decoding in ADF7023 is implemented complementary . You can encode some bytes according to...
View ArticleEVAL-ADF70XXMBZ2
hii am currently evaluating EVAL-ADF7021DBZX using EVAL-ADF70XXMBZ2 mother board.i am interested to know how you implemented the Chip Programming Software.the purpose of my study is to be able to know...
View ArticleADF7021-N CLKOUT frequency
Hi!I am working with the ISM transceiver ADF7021-N and I´d need to know the value of the frequency , by default, of the CLKOUT signal from the SPI interface.I can not find it on the datasheet, Thank...
View ArticleAbout how to use ADN2818
So I'm outsider of SONET, I query you about foundamental usage of ADN2818. Q1.I want to use it as clock and data separater from "enbedded clock signal" like a 8B10B. If it possible,Q2.Dose it can...
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View Article