Difference between ADN8834CB-EVALZ and ADN8834MB-EVALZ
What is the difference between ADN8834CB-EVALZ and ADN8834MB-EVALZ? Do you have any additional information or datasheet for the eval kits?
View ArticleLiedi
Hello,i have to develope a 4 channel EMG-measurement system by very small power consumtion and optimal chip disign. For input stages i found in the literature only dc-coupled instrumentation amplifiers...
View ArticleDivision with AD538
I am trying to do on-board division with the AD538 chip. I have to voltage inputs which can have either negative or positive polarity. The discussed cases in the data sheet are clear for when the...
View ArticleADF7012 RF output impedance
Dear, Can anyone kindly provide us RF output impedance of ADF7012 around 145MHz?We'd really appreciate if anyone has data on this as we're not equipped with load-pull measurements. Thank you in...
View ArticleAD630 Lock-in Amp
Hello everyone, I am looking to implement a lock-in amplifier in the range of 100kHz to 1MHz to obtain amplitude and phase information. Any thoughts on whether the AD630 will be ok for this frequency...
View ArticleSimulation software and a library for ADN3000-06 ic
I am a university student doing my final year university project.Part of My project is to design a fiber optic receiver.I am employing Analog devices ADN3000-06-50A-PT7 ic for this purpose.I am...
View ArticleADA4571 Evaluation Software doesn't be opened
Hi All, I am now trying to install the ADA4571 Evaluation Software into my PC, it doesn't work so far.I am trying to install it along with the installation procedure written in theUG-739.The software...
View ArticleADF7021, 3FSK modulation and supported data rate?
Hi everyone, I am wondering if ADF7021 supports baud rate 19.2 Kbps with 3FSK modulation? Thanks
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View ArticleClik here to view.
demodulation sin o square wave?
Hi,i'd like to use AD8333 to demodulate a pass-band signal with 200kHz local oscillator.The datasheet says that i can use both sin wave and square wave. My question is:The use of a square wave produces...
View ArticleEVAL-ADF7021DBZ5 for ADF7021
Hi all,I wanna ask about ADIsimSRD Design studio for Eval-ADF7021DBZ5. Introduction:- My team wanna make nanosatellite communication payload using ADF7021with the spec= Rx = 145.95 MHz (single...
View ArticleClik here to view.
AFC or linear demodulation ?
Hi,In the RF chipset we use (adf7021-n), we have the option AFC enable or not.Could you explain me the advantages and drawback of the two demodulation method ? We use 2FSK, 9600bps. Thank you Cedric
View ArticleADF7021 vs ADF7021-N register differences
Hello, Beyond the Register 1 changes required based on the output frequency, are there any other register differences between the ADF7021 and ADF7021-N? I am trying to use the same register settings...
View ArticleADN8831 - Which FET should I use?
Hi, I have a customer developing a circuit based on AN-695 schematic. The FET indicated (FDC6020C) is obsolete, so I would like to know which other FET's can I recommend them. Thanks,Fernando Guerra
View ArticleThe ADF7023 the AES encryption and decryption functions configuration Issue
First of all, my experiment is described as follows:with single-chip SPI and GPIO, MOSI, MISO, SCLK, CSN, and IRQ_GP3 pick heel ADF7023 connection.firmware running on a single-chip-based...
View Article3 lead ECG
I am planning to build a wireless ECG sensor. This is my first attempt to do anything of this sort. I was wondering if i should go AC-coupled AFE or DC-coupled AFE? Which one would be easier?
View ArticleAD22151 Eval Board
Hello, I am looking for an eval board for the AD22151. Is there one that is available? Thanks!
View ArticleA series of questions about ADATE318
1. How to get the ibis model of the ADATE318?2. What the difference between the pin PPMU_Sx and PMU_Sx? How to use these pins in application?3. How to connect the kinds of GND in the application, such...
View ArticleClik here to view.
ADAS1000 CMRR
Hi, We have a customer who is designing the ECG devices but there is a requirement on the CMRR (Balanced) of > 120dB at mains frequency, with patient cable. Can ADAS1000 perform such a CMRR...
View Article