adf7021-N
what exactly are the output pins mix_i and mix_q and fil i and fil q for? image rejection how do i know the signal i'm getting is lower one or higher one with respect to reference signal
View ArticleClik here to view.
Need ADF7023 Evaluation board Information
Hello! This is Abi, I am a student and I am working on the project of Wireless Communication, and I am using EVAL-ADF7XXX_MB3Z.Actually i didn´t have any proper datasheet for it, because I am really...
View ArticleADC clock- jitter vs clock phase-noise
Phase jitter is expressed in a number of radians "RMS" phase jitter (time domain) within a band of frequencies.For ADC clock specifications. An important ant performance parameter is: clock jitter...
View ArticleADF7023 Transceiver Problems
Hi ! Here is some ADF7023 issues . please check if they should be added in errata . 1) Manchester coding and decoding in ADF7023 is implemented complementary . You can encode some bytes according to...
View ArticleEvaluation of ADF7023
Hi, I want to test the ADF7023. Therefore, I want to set up a simple network with one chip in transmit mode and one in receive mode (spatially seperated from each other, about 30m). Do I need 2...
View ArticleSoftware drivers for ADF7023-J
I have a design using the ADF7023-J xceiver and was trying to pull in software to initialize & configure it with my Atmel micro. I downloaded the adf7023.c and adf7023.h files which appear to have...
View ArticleADF7021-N,RSSI level always 0.Where is my error?
Hi to everybody in this forum,thanks in advance just for reading this My firmware is not able to read RSSI level on ADF7021-N mounted on a specific board The board itself can be connected to the Eval...
View ArticleGFSK testing at 2.4GHz
Hello, I am looking for solution of GFSK testing in 2.4GHz.The product is based on ADF7242 Transceiver.What test equipment can you recommend? Thank you
View ArticleClass D micro smd amplifier marking
Hi,I'm trying to identify this IC. This is the best magnification I can get of it and it looks like :-0BU600 (it could be 08U600) BP 27I have a number of these and the top line changes but the BP 27...
View ArticleAD630 Lock-in Amp
Hello everyone, I am looking to implement a lock-in amplifier in the range of 100kHz to 1MHz to obtain amplitude and phase information. Any thoughts on whether the AD630 will be ok for this frequency...
View ArticleEVAL-ADF70xx driver problem
I've EVAL-ADF70xxMBZ2 recently procured to use with EVAL-ADF7021 (and 7021-N). I had installed previous version of ADISIMLINK on my computer so i tried the provided "purge_ADIismLink" to clear the...
View ArticleI purchased PN EPM7192SSQC160-10N dc 1149. They had form and shear marks and...
The above devices appeared to be in original condition all showing form and shear marks on the leads but when I tested the top surface with some heated solvents the surface came off and there was no...
View ArticleADF7242 Max. Input power.
I want to use ADF7242 for long range communication. Could you tell me how many max input power for ADF7242 , if I will add LNA in RF front end ? Thank you.
View ArticleEMG Isolation in the case of a processor with an in-built ADC.
Hello Bill,I went through a discussion initiated by Yee http://ez.analog.com/thread/6389?tstart=0 in which you have discussed choosing an appropriate isolation scheme for an ECG system. I too have...
View ArticleAD630 Lock-in Amp
Hello everyone, I am looking to implement a lock-in amplifier in the range of 100kHz to 1MHz to obtain amplitude and phase information. Any thoughts on whether the AD630 will be ok for this frequency...
View ArticleADF7242 Receiver Latency
I am interested in getting a packet through for a trigger event with minimal latency. The data sheet for the ADF7242 specifies transmitter latency, at least for the SPORT mode. What is the associated...
View ArticleADN2830 Laser Diode Controller
I have spun a board for the ADN2830 to control a JDSU laser with internal photo detector. The good news is both the cathode and anodeare isolated from the case. I'm using two in master/slave as I need...
View ArticleHow can I get the ADRadioNet for ADF7023?
Is the protocol developed by ADI available for ADF7023?How can I download it?
View ArticleADF-7020-1 PN9 TX Test Mode - What Register Setting ???
The data sheet for the ADF7020-1 doesn't show how to enable a PN9 TX test mode. Yet, this feature appears to be available, as it is possible to enable it through the ADF7020-1 Config Software...
View ArticleADF4007 PLL
Hello .; I am using ADF4007 PLL in my application board. PLL loses lock when, I try to read either R or N divider at MUXOUT pin. What would be the possible reason/s?Supplementary question: Would it be...
View Article