ADATE318 IBIS model
Hi ADIer, Where can I find the IBIS model of ADATE318? I can not do simulation without it. I can't find a suitable place to put this request, ADATE318 integrated DACs, maybe I can put it here. Thanks...
View ArticleLow output swing at the output of ADCMP 562 Evaluation board
Hi, We have purchased the ADCMP 562 evalutaion board. I have provided the proper supply voltage to the chip such as VEE( -5.2V), VCC_IN (+5V), VDD_IN (+3.3V). Do I need to provide voltage to VTERM...
View Article320*240 resistive touch screen calibration problem
Hi every one.I have 320*240 LCD with resistive touch screen and touch screen controller of AD7843 ( All is together in one LCD from topway: KM2088S). I want to know what is the best way to calibrate...
View ArticleSupply voltage for temp sensor ADATE318
What is supply voltage (VDD_TERM) for temp sensor ADATE318. I did not find this information in the datasheet.
View ArticleA series of questions about ADATE318
1. How to get the ibis model of the ADATE318?2. What the difference between the pin PPMU_Sx and PMU_Sx? How to use these pins in application?3. How to connect the kinds of GND in the application, such...
View ArticleADF7020-1 question
I want to be able to offer two frequency ranges, one being ~600MHz and the other being ~900 MHz. I'm wondering if I can expand the range of the 7020-1 to get up to the 900MHz. It looks like the -1...
View ArticleClik here to view.
Difference between ADN8834CB-EVALZ and ADN8834MB-EVALZ
What is the difference between ADN8834CB-EVALZ and ADN8834MB-EVALZ? Do you have any additional information or datasheet for the eval kits?
View ArticleClarification on interfacing ADF7020
Hello, I am using ADF7020 (daughter board with 11.0592MHz XTAL) to design a RF UHF reader which reads the data in the RFID tag (passive), as the tag comes within the range. I use dsPIC33fj256gp710 for...
View ArticleADF7242 and frequency hopping in GFSK/FSK mode
Hello, I am looking at using the ADF7242 for a proprietary Frequency Hopping radio link.I would like to determine the blanking interval, i.e. how long it will take to hop between frequencies. Referring...
View ArticleADCMP572 VTT pin confusion
We've received 2 ADCMP572 eval boards, but unfortunately the documentation for the part and the eval board seems to be inconsistent.As a result, I have a question: should VTT (pin 8) be tied to GND or...
View ArticleAD8212S
Good afternoon, I can't find any information about pins forming for creating footprints in Mentor Graphics. Would you be so kind to help me? Best regards Andrey
View ArticleADF7242 Max. Input power.
I want to use ADF7242 for long range communication. Could you tell me how many max input power for ADF7242 , if I will add LNA in RF front end ? Thank you.
View ArticleClik here to view.
ADATE318 IBIS model
Hi ADIer, Where can I find the IBIS model of ADATE318? I can not do simulation without it. I can't find a suitable place to put this request, ADATE318 integrated DACs, maybe I can put it here. Thanks...
View ArticleEMG Isolation in the case of a processor with an in-built ADC.
Hello Bill,I went through a discussion initiated by Yee http://ez.analog.com/thread/6389?tstart=0 in which you have discussed choosing an appropriate isolation scheme for an ECG system. I too have...
View ArticleHow to configure the AD9866 registers?
I am using the AD9866 bidirectional DAC and ADC chip. And now I am encountering an issue that don't know how to configure the registers in the AD9866.Is there somebody can guide me the correct...
View Article[ASK] ADF7021 (EVAL-ADF7021DBZ5)
Dear all, I bought these components from analog devices : 1. EVAL-ADF7021DBZ52. EVAL-ADF70XXMBZ2 I want to make transceiver based on these specifications : 1. Uplink frequency: 145.95 MHz2. Downlink...
View ArticleHow to log the max G-force between Samples
Hi, Does anyone have an idea, how I can "capture" the maximum voltage of a Gforce sensor between 2 samples of a low speed, low power AD convertor? Kind regards, John van Zijl
View ArticleADF7021-N CLKOUT frequency
Hi!I am working with the ISM transceiver ADF7021-N and I´d need to know the value of the frequency , by default, of the CLKOUT signal from the SPI interface.I can not find it on the datasheet, Thank...
View Article3 lead ECG
I am planning to build a wireless ECG sensor. This is my first attempt to do anything of this sort. I was wondering if i should go AC-coupled AFE or DC-coupled AFE? Which one would be easier?
View ArticleClik here to view.
AD5273 Programmable Digital Potentiometer
We use the AD5273 for adjusting contrast on a LCD we use in our design. The LCD is changing and we no longer need the AD5273 to adjust contrast but we have to leave the AD5273 in the circuit because...
View Article